Roadsafe Mitsubishi Triton MN

Tail Shaft Spacer 13.25mm – Mitsubishi Triton ML / MN / MQ [TSSTRI] Diff drop kit for the Mitsubishi Triton. Lowering the front differential after a lift brings the CV angles back to where they should be, which is what stops boots tearing and joints wearing out early.Bolts in using the factory mounting...

Add to cart

Coil Strut Spacer 10mm (Pair) – Mitsubishi Triton ML/MN/MR & Pajero Sport [CSSTRI10] Spacer for the Mitsubishi Triton. A straightforward way to pick up ride height or level out a front end that sits low against a bull bar.Machined from solid, with the hardware where required.

Add to cart

Coil Strut Spacer 25mm (Pair) – Mitsubishi Triton ML/MN/MR & Pajero Sport [CSSTRI25] Spacer for the Mitsubishi Triton. A straightforward way to pick up ride height or level out a front end that sits low against a bull bar.Machined from solid, with the hardware where required.

Add to cart

Battery Tray – Mitsubishi Triton 07-13 [BT016] Battery tray for the Mitsubishi Triton. Holds a second battery solidly enough for corrugations, using the existing body mounts — no cutting or drilling.Powder coated, with the clamp and hardware included.

Add to cart

Battery Tray - Black – Mitsubishi Triton 07-13 [BT016-BLACK] Battery tray for the Mitsubishi Triton. Holds a second battery solidly enough for corrugations, using the existing body mounts — no cutting or drilling.Powder coated, with the clamp and hardware included.

Add to cart

Bash Plate – Mitsubishi Triton ML-MN / Challenger 2007-2013 - 3rd Plate [BP017-3] Steel underbody protection for the Mitsubishi Triton andMitsubishi Pajero. Bolts to the factory mounting points and takes the hit that would otherwise land on your sump, steering or transfer case.Supplied with the mounting hardware.

Add to cart

Bash Plate – Mitsubishi Triton ML-MN / Challenger 2007-2013 - 4th Plate [BP017-4] Steel underbody protection for the Mitsubishi Triton andMitsubishi Pajero. Bolts to the factory mounting points and takes the hit that would otherwise land on your sump, steering or transfer case.Supplied with the mounting hardware.

Add to cart

Upper Ball Joint Pair extended 25mm – Mitsubishi Pajero (Nm/Np) 99-On /Triton (ML/Mn) 06-On - Min 60mm Lift Req For Fitment (Does [BJ4082PAIR] Heavy duty ball joint for the Mitsubishi Triton andMitsubishi Pajero. Built stronger than the factory item, with the extended versions correcting the geometry once a lift kit has been fitted.Sold as listed — check whether you need one side or...

Add to cart

Upper Ball Joint extended 25mm – Mitsubishi Pajero (Nm/Np) 99-On /Triton (ML/Mn) 06-On [BJ4082] Heavy duty ball joint for the Mitsubishi Triton andMitsubishi Pajero. Built stronger than the factory item, with the extended versions correcting the geometry once a lift kit has been fitted.Sold as listed — check whether you need one side or...

Add to cart

Rear Extended Shackles (Pair) – Mitsubishi Triton ML / MN [SK405EXT] Recovery gear for the Mitsubishi Triton. Rated equipment for winching and snatch recoveries, made to the Australian standard for the job.Check the rating against your vehicle’s weight before you use it.

Add to cart

Recovery Tow Point – Mitsubishi Triton MN [RPTRI02KIT] Upgrade your Mitsubishi Triton's towing setup with this Roadsafe / Mr. Hitches Towing Accessory (Part No. RPTRI02KIT). Engineered to handle the demands of heavy towing — whether you're running a caravan, boat, or trailer on outback roads. Verify tow ball...

Add to cart

Rated Recovery Tow Point (Pair) – Mitsubishi Triton ML-MN 2005-15 [RPTRI02] Rated recovery point for the Mitsubishi Triton. Bolts to the chassis rail with high-tensile hardware and gives you somewhere honest to attach a strap — a tie-down loop is not a recovery point.Engineer rated and supplied with the correct bolts.

Add to cart

Bash Plates (2) – Mitsubishi Triton ML-MN / Challenger 2007-2013-Plates 1 & 2 [BP017-PACK] Steel underbody protection for the Mitsubishi Triton andMitsubishi Pajero. Bolts to the factory mounting points and takes the hit that would otherwise land on your sump, steering or transfer case.Supplied with the mounting hardware.

Add to cart

Bash Plate – Mitsubishi Triton ML-MN / Challenger 2007-2013 - 2nd Plate [BP017-2] Steel underbody protection for the Mitsubishi Triton andMitsubishi Pajero. Bolts to the factory mounting points and takes the hit that would otherwise land on your sump, steering or transfer case.Supplied with the mounting hardware.

Add to cart

Bash Plate – Mitsubishi Triton ML-MN / Challenger 2007-2013 - 1st Plate [BP017-1] Steel underbody protection for the Mitsubishi Triton andMitsubishi Pajero. Bolts to the factory mounting points and takes the hit that would otherwise land on your sump, steering or transfer case.Supplied with the mounting hardware.

Add to cart

Control Arm – Mitsubishi Triton MN (Front, Lower, RH) [BJ3250R+ARM] Get your Mitsubishi Triton's suspension geometry back to factory spec with this Roadsafe Control Arms (Part No. BJ3250R+ARM). A direct-fit replacement (Right Hand (RH)) that eliminates the knocking, vibration, and abnormal tyre wear caused by worn arm assemblies. Built to...

Add to cart